Plastics Machinery Shipments Escalated Sharply in Q4
Continued investment is expected to persist throughout this year as well.
Shipments of plastics machinery posted a robust rise in the fourth quarter of 2014, according to statistics compiled and reported by SPI: the Plastics Industry Trade Association’s Committee on Equipment Statistics (CES).
“Annual shipments of plastics machinery increased for the fifth straight year in 2014, and the economic fundamentals that favor continued investment in capital equipment are expected to persist through 2015 as well,” according to Bill Wood, the plastics market economist who analyzes and reports on the plastics machinery market sector for the CES.
Shipments of primary plastics equipment (injection molding, extrusion and blow molding equipment) for reporting companies totaled $346.1 million in Q4. This was 9.8 percent higher than the revised shipments total of $315.1 million in Q3 of this year, and it was up a solid 8.0 percent when compared with the total from Q4 of 2013. For 2014 as a whole, the total value of primary equipment shipments was up 7.6 percent compared with the annual total from 2013.
A closer look at the CES data shows that the shipments value of injection molding machinery advanced 7.7 percent in Q4 of 2014 when compared with the total from Q4 of 2013. For 2014 as a whole, shipments of injection molding machinery were up 5.3 percent when compared with the annual total from 2013. The shipments value of single-screw extruders increased 1.1 percent in Q4 when compared with last year. For 2014 as a whole, single screw extruder shipments were down 3.0 percent.
The value of shipments of twin-screw extruders (which includes both co-rotating and counter-rotating machines) climbed 8.2 percent in Q4. For 2014 as a whole, shipments of twin screw extruders jumped 26.3 percent. The shipments value of blow molding machines advanced 10.2 percent in Q4. For 2014 as a whole, shipments of blow molding machinery spiked up a sparkling 38.1 percent.
The CES also compiles data on the auxiliary equipment segment (robotics, temperature control, materials handling, etc.) of the plastics machinery industry. New bookings of auxiliary equipment for reporting companies totaled $103.5 million dollars in Q4. This represented a gain of 2.2 percent when compared with the total from Q4 of 2013. For 2014 as a whole, bookings of auxiliary equipment were up 9.2 percent.
The trend upward in the CES data on plastics machinery shipments corresponds with the long-term trends in the two major data series compiled by the U.S. government that measure overall demand for industrial machinery. According to the Bureau of Economic Analysis, business investment in industrial equipment escalated by 16 percent (seasonally-adjusted, annualized rate) in Q4 when compared with Q4 of 2013, and the annual total for investment in 2014 was up a vigorous 13 percent.
The other important machinery market indicator, compiled by the Census Bureau, showed that the total value of new orders of industrial machinery jumped 20 percent in Q4 when compared with the total from Q4 of 2013, and for the year as a whole in 2014 industrial machinery orders were up a stellar 30 percent.
"The short-term problems caused by a stronger dollar and a downsized oil patch notwithstanding, the recovery in the US economy will continue through 2015. The stock market is still at an all-time high. Corporate profits are still at record levels. And as I have said before, the three main trends that will drive the economy over the coming months are already well-established. They are: low interest rates, low energy prices, and rising wages and household incomes resulting from stronger employment levels," said Wood.
The CES also conducts a quarterly survey of plastics machinery suppliers that asks about present market conditions and expectations for the future. The responses from the Q4 survey indicate that machinery suppliers remain optimistic about the market demand for their products in the coming months. When asked about expectations for future market conditions, 92 percent of the respondents expect conditions to stay the same or even improve in the coming quarter, and 94 percent expect them to hold steady or get better during the next 12 months.
There was a strong consensus that North America is the global region where the most promising market conditions for machinery suppliers are expected in the coming year. Expectations for Mexico were also quite high. Expectations for Latin America call for mostly steady market conditions, and this is a bit of an improvement from the last quarter. Expectations for Asia and Europe, which were mostly unchanged from Q3, call for demand to hold steady.
As for the major end-markets, the respondents to the Q4 survey still expect that automotive and medical will remain strong in terms of demand for plastics products and equipment. Expectations for all other end-markets call for steady-to-better demand to prevail in 2015.
The industry and survey analysis that appears in this media report was contributed by Bill Wood of Mountaintop Economics & Research, Inc., a supplier of market analyses and forecasts for decision makers in the plastics Industry. Mr. Wood is a plastics market economist with more than 28 years of experience in industrial market analysis and forecasting. (billwood@plasticseconomics.com)
The SPI Committee on Equipment Statistics (CES) collects monthly orders and shipments data from manufacturers of plastic injection molding, extrusion, blow molding, thermoforming, hot runners and auxiliary equipment. A confidential, third-party fiduciary, VERIS Consulting, LLC (VERIS), compiles the monthly data and analyzes individual company data for consistency and accuracy. Once this crucial process is completed, VERIS aggregates and disseminates reports to participating companies. If this is something you and your company are interested in please contact Katie Masterson at kmasterson@plasticsindustry.org or 202-974-5296.
Related Content
Confronting the Mold Design Talent Drought
Recently, I reposted on LinkedIn the results of an informal survey we conducted, which revealed a shortage of skilled mold designers. It quickly gained a lot of traction. Given the response, I thought I'd summarize the feedback and keep the conversation going.
Read MoreMMT Chats: 5 in 5 with Best Tool and Engineering
MoldMaking Technology Editorial Director Christina Fuges reveals 5 best practices for improving efficiencies within shops...in 5 minutes. Our guest is Joe Cherluck, President of Best Tool and Engineering in Clinton Township, Michigan.
Read MoreWhat is Scientific Maintenance? Part 2
Part two of this three-part series explains specific data that toolrooms must collect, analyze and use to truly advance to a scientific maintenance culture where you can measure real data and drive decisions.
Read MoreMaking Mentoring Work | MMT Chat Part 2
Three of the TK Mold and Engineering team in Romeo, Michigan join me for Part 2 of this MMT Chat on mentorship by sharing how the AMBA’s Meet a Mentor Program works, lessons learned (and applied) and the way your shop can join this effort.
Read MoreRead Next
How to Use Continuing Education to Remain Competitive in Moldmaking
Continued training helps moldmakers make tooling decisions and properly use the latest cutting tool to efficiently machine high-quality molds.
Read MoreHow to Use Strategic Planning Tools, Data to Manage the Human Side of Business
Q&A with Marion Wells, MMT EAB member and founder of Human Asset Management.
Read MoreReasons to Use Fiber Lasers for Mold Cleaning
Fiber lasers offer a simplicity, speed, control and portability, minimizing mold cleaning risks.
Read More