10/18/2019 | 4 MINUTE READ

How to Select a Mold Temperature Controller

Facebook Share Icon LinkedIn Share Icon Twitter Share Icon Share by EMail icon Print Icon

White paper shares how cooling channel analysis, which collects maximum pressure drop, total flow rate and heat dissipation, eases the performance evaluation of mold temperature controllers. 



Facebook Share Icon LinkedIn Share Icon Twitter Share Icon Share by EMail icon Print Icon

This recent white paper from Moldex3D sheds some light on a few things mold builders should know before investing in a mold temperature controller:


In injection molding, we usually control the mold at a fixed temperature by making coolant continuously flow through the mold. If the coolant flow is not enough, or the coolant temperature is not as expected, the mold temperature won’t be able to keep at the designated temperature. The manufacturers of mold temperature controllers calculate the appropriate mold temperature controller specifications according to the size of the mold and the part. However, it can be a challenge for engineers and analysts using the simulation software to evaluate the performance of a mold temperature controller.

Here are a few principles for using CAE software to better evaluate the performance of mold temperature controllers.

  1. In Moldex3D’s Flow analysis settings, users can apply two types of boundary conditions for cooling channels: flow rate and pressure. When the coolant flows through the cooling channel, the flow rate at the inlet and outlet are equal. Users only have to measure the flow rate at one side of the cooling channel, and the flow rate at the other side can be attained. So, using the flow rate as the boundary condition is easier to control. In terms of pressure, the inlet pressure is higher than the outlet pressure, and the flow is caused by this pressure difference. The default value of the outlet pressure is zero. Users only have to set the pressure boundary at the inlet, and this value will be equal to the pressure difference between the inlet and outlet. If we create a plot to show the relationship between the cooling channel flow rate and pressure, we can see that as the flow rate gets larger as the pressure difference gets larger. The two parameters are approximately proportional.




  1. Apart from the pressure difference, flow resistance  is another factor that will affect flow. Flow resistance varies with some conditions, such as cooling channel diameters, channel length, channel wall smoothness, coolant properties, and flow rate. The Darcy–Weisbach equation shows the relations between these parameters.



  1. The  function of a mold temperature controller is to push the coolant to flow and stabilize the coolant temperature. The main function of the pump in the mold temperature controller is to push the coolant to flow. When the pump pressure rises, the flow rate decreases; when the flow rate increases, the pump pressure decreases. We can see the maximum flow rate and maximum pressure values on the mold temperature controller specification, but we have to note that the two conditions never exist simultaneously. We can see the mold temperature controller pressure is inversely proportional to the flow in the figure below.
  1. Users can obtain the flow rate and pressure difference of every cooling channel through cooling channel analysis. The total flow rate of the cooling channels is the flow the mold temperature controller has to provide. The maximum pressure in the cooling channel is the minimum pressure the mold temperature controller has to provide. Users can enter point coordinates of the total flow rate and maximum pressure differences in the line graph. If the coordinate point is below the line, it means the mold temperature controller is able to provide enough flow rate and pressure. If the coordinate point is above the line, it means the mold temperature controller is not able to provide enough flow rate and pressure. The latest version of Moldex3D, R17, is now able to provide the data of maximum pressure drop, total flow rate, and heat dissipation. Users can evaluate the mold temperature controller’s performance by adopting the pump performance curve.







  • Moldmaking Gets Wyrd—and Amazing—with All-Digital Sculpting

    By early 2012, when the price of white metal had increased 80 percent over the past two years— eating into revenues and margins—Wyrd was forced to rethink its approach. Ghost Studio, a Longmont CO-based product design firm, and Geomagic, maker of 3D software solutions from scan to design to manufacturing, soon presented Wyrd with a smarter way.

  • Five Ways to Efficiently Tackle Shop Floor Management

    Even the smallest mold shop can afford an integrated shop floor management system that allows for the management of every business transaction—from quote to cash—and is an invaluable tool for ensuring efficiency.

  • The Feature Technology Feature of CAD/CAM

    CAM software should have forward looking features that allow you to work in a traditional programming approach and to step up into a more organized environment that includes storing process knowledge and corporate experiences.