GETMOREINFO

For more information contact Surface Treatment Technologies, Inc. (Baltimore, MD) at (410) 332-0633, via e-mail at info@stt-inc.com or via its website at www.stt-inc.com.

MMTTOOLS

 Print This Article

Figure 1: ESD overlay on a mold eliminated the burr being produced in the part.

What makes this process stand out is that ESD accomplishes these tasks without the need for preheating or postheating the repaired component. The low heat input of the process results in no degradation of the repaired component's microstructure as a result of the repair. Often, the parts can be repaired on-site - greatly reducing downtime and the need for mold inventory, which has a measurable positive effect on productivity and operating costs.

The Process
The process differs from plating and other coating processes in that it produces a true metallurgically bonded coating. This is accomplished without introducing sufficient heat in the workpiece to induce thermal damage, as can be evident with welding and even microwelding processes. Deposition of alloys using the ESD process is accomplished using a consumable electrode in which a capacitive discharge melts and accelerates the electrode material onto the workpiece. This transfer of materials occurs in plasma that forms on discharge of the spark - resulting in a strong metallurgical bond with the substrate due to instantaneous melting in the plasma. Figure 2a illustrates the process at the point of contact with the workpiece and the micrograph in Figure 2b demonstrates the interface and coating - showing the integrity of the ESD-applied coating.

Figure 2a: ESD process schematic

Figure 2b: ESD-applied Ni alloy on D6AC steel.

Extremely rapid pulse times prevent heat generation in the part being repaired or coated. This low heat input eliminates distortion in parts and eliminates the need for post-repair heat treatment because there is no degradation of the surrounding metal in the repaired component. Further, the ESD equipment is designed to enable flow of inert gas to the coating/overlay area to prevent oxidation and impurities from becoming entrapped in the deposited layer.

Figure 3: Chart of hardness values of a repaired plate of D6 steel.

Hardness values of the coated area in metals show that there is no measurable heat- affected zone (HAZ) and no reduction in hardness (see Figure 3). The extremely rapid melting and deposition of the metal coating or overlay also creates a very fine microstructure (a nanograined microstructure) - giving desirable hardness and surface properties. The graph in Figure 3 shows hardness measurements taken in the base part and the overlay (repaired) area showing comparable hardness to the base metal and even a slight increase as a result of the finer-grained microstructure of the deposited metal.

Applications
The ESD process can be applied to conductive metal substrates and has been demonstrated to be successful on components of low- and medium- carbon steels, tool steels, die and mold alloys, cast irons, cast steels, stainless steels, aluminum alloys, copper alloys and other alloys with sufficient electrical conductivity. Electrical conductivity is the key property that dictates capability to use the ESD process on a part repair or coating. Many metals combinations have been successfully applied. In some cases, the metal electrode does not have to match the workpiece composition to produce high-quality dense overlays and coatings. Electrodes also can be made in various shapes to provide the best means of access to the area to be coated. The chart in Figure 4 shows the various metals and alloys that have been applied to metallic substrates using the ESD process.

Figure 4: Listing of alloyos that have been applied to metallic substrates using ESD process.

Electrodes come in numerous shapes and sizes to address specific needs of intended applications. Hardware can be adapted to reach IDs and non-line-of-sight applications. Figure 5 shows some of the electrode shapes used with ESD equipment.

Figure 5: Typical range of ESD electrode shapes and sizes.

There are two different models of ESD units offering four different power levels to address varying needs of users. One type of unit features higher power at three levels and would be most utilized in higher volume shops. Another unit affords fine control for smaller jobs. There are multiple applicator heads available to address different coating and overlay (repair) requirements. These equipment units are easy to operate with minimal training, are very portable and can be used for on-site repairs - eliminating the need to remove large dies from service. This aspect not only saves production downtime, but also can alleviate the need to stock additional molds in inventory. The ESD units may be used with hand applicators for individualized control of a coating, or can be integrated with robotic controls for mechanized and repeatable process controls. These applications are shown in Figures 6a and 6b.

Figure 6a: Hand application on a part.

Figure 6b: ESD being applied using robotic control of the applicator.

The ESD process also has been shown to protect die-casting dies from liquid metal erosion, scoring and heat checking with the deposition of hard carbide coatings such as WC, TiC, TiB2, Cr3C2 and VC. The carbide coatings have demonstrated improved liquid metal flow, improved release and reduced scuffing of die cast products. Hard coatings also can be used to extend the life and improve the performance of cutting tools (see Figure 7).

Figure 7: ESD-applied WC/Co coating on 4340 (etched).

Numerous Asian and European companies utilize the ESD equipment as part of their preventive and restorative maintenance procedures. The process is used extensively in the plastics industry in Japan to protect and rebuild injection molds. ESD is also widely used in the die casting industry for die repair, die protection and also is used for casting defect repairs.