LEARNMORE

How to Prevent Seizing and/or Galling of Wear Plates, Slides And Core Pins
Using PVD/PACVD surface treatments can produce a desired tribological behavior without a costly change to design or material.

How Surface Treatments Keep
Molds Operating Longer
Important tips and information about mold coatings to help you achieve the level of production that you and your customers desire.

 Mold Design & Modeling Zone

GETMOREINFO

For more information visit the MMT Showroom for Oerlikon Balzers Coating USA Inc.

MMTTOOLS

 Print This Article

PET bottle core coated with low-temperature titanium nitride coating. Image courtesy of Oerlikon Balzers.

Conventional PVD Coatings
Only a few microns thick and harder than steel, PVD (Physical Vapor Deposition) coatings such as TiN, TiAlN and CrN are useful tools for moldmakers and molders. Their high hardness imparts abrasive wear resistance while their ceramic composition resists corrosion and enhances mold release. Because of this inherent lubricity, PVD-coated tools have the additional advantage of increasing flow for faster mold filling and shorter cycles.

Key applications of PVD coatings are on ejector guide elements, cavities and cores where the coatings’ tribological properties protect against seizure and corrosion. Internal lubricants and release agents can in some cases be eliminated. The coatings’ hardness and wear resistance protect molds from highly glass- or mineral-filled resins, as well as hot-gas corrosion from materials like PVCs and CPVCs.

PVD coatings for tools are conventionally applied by arc deposition temperatures between 400 and 500°C (750 to 930°F), which makes them well suited for steels with higher tempering temperatures including M2 and CPM grades. However, this high deposition temperature made PVD coating unfeasible for a wide variety of cold working steels, copper alloys and die steels that are used in plastic processing.

Lower Deposition Temperature = Greater Choice of Materials
Now, a new arc technology permits coating deposition at temperatures as low as 200°C (390°F). This lower temperature allows mold materials with lower tempering thresholds to be coated without distortion, loss of hardness or reduction in corrosion resistance, and the PVD coatings have no performance loss compared to those deposited at higher temperatures.

Lower coating deposition temperature allows mold materials with lower tempering thresholds (AISI 420 in this example) to be coated without reduction in corrosion resistance. Graphs courtesy of Oerlikon Balzers Coating USA Inc.

This technology not only improves the productivity and tool life of existing mold components, but also allows moldmakers, designers and molders a greater material choice when designing new molds and components. Improved durability, higher surface hardness and increased service temperatures can be achieved from less expensive, easier to machine mold materials including cold-working steels, die steels and copper alloys.

This article discusses three high-performance nitride coatings produced by the lower temperature arc evaporation process, which will be of particular interest to moldmakers: a titanium nitride coating¹, a monolayered chromium nitride coating² and a nano-layered titanium aluminium nitride coating³.

Improved Demolding
Surface disturbances on molds and components can be a leading cause of demolding issues, particularly for molds made of steels with lower surface hardness. These surface disturbances can be due to the properties of the mold material (such as porosity) or because of the breakdown of the mold over time (caused by the effects of resins). A new low temperature deposition process for titanium nitride coating has been designed to improve demolding and filling as well as provide enhanced mold surface protection.

It has a surface hardness of 2300HV and a coefficient of friction against steel of 0.4. These properties help prevent the buildup of resins, increase wear-resistance and provide a surface that is easier to clean. The inert properties of this low deposition temperature PVD make it ideal for molds working in linear polyesters (PC, PBT(B), PET(P)) and styrene polymers (PS, SB, SAN, ABS, ASA). Additionally, this coating is biocompatible and safe for food contact.

Lower coating deposition temperature allows mold materials with lower tempering thresholds (AISI 420 in this example) to be coated without distortion.

Wear, Corrosion and Oxidation Resistance
Moldmakers may be familiar with hard chromium plating. Applied at low temperatures, this coating is widely used to improve hardness and corrosion resistance. A monolayered chromium nitride coating that shows better corrosion resistance, significantly higher hardness (1750HV versus 1245HV for hard chromium), better coating adhesion, and improved resistance to abrasive wear is available. It has a coefficient of friction against steel of 0.5 and a maximum service temperature of 700°C (1290°F).

These properties give plastic injection molds an advantageous combination of wear, corrosion and oxidation resistance. This coating is well suited for coating molds that work in plastics that, during processing, outgas chlorine, fluorine or other aggressive volatile contents, including: polyolefins (PE, PP, PB), acetal resins (POM), polyamides (PA), linear polyesters (PC, PBT(B), PET(P), and polyaryis/polysulphones (PPE, PEEK, PAEK/PPS, PSU, PES).

Hardness and Stability
The higher hardness properties of PVD help to protect the surfaces of mold components from highly glass- or mineral-filled resins. The new low temperature process for the nano-layered, titanium aluminium nitride coating has a microhardness of 3300HV and features high levels of oxidation resistance. It has a coefficient of friction against steel of 0.30 - 0.35 and a maximum service temperature of 900°C (1650°F).

Lower coating deposition temperature allows mold materials with lower tempering thresholds (AISI D6 in this example) to be coated without loss of hardness.

These are ideal for plastic injection molds with textured surfaces and for working in engineered plastics including polyamides (PA) and polyaris/polysulphones (PPE, PEEK, PAEK/PPS, PSU, PES). It is also well suited for the processing of melts with fiberglass reinforcement and die-cast aluminum molds.

Summary
Applied at temperatures as low as 200°C (390°F), these coatings retain all of the properties of standard PVD coatings. The lower deposition temperature allows for the coating of mold materials that would distort under the higher deposition temperatures of previous generation PVD coatings.

This coating technology gives moldmakers, designers and molders a greater material choice when designing new molds and components without having to sacrifice mold performance or life.

References
¹ BALINIT® A ARCTIC (TiN).
² BALINIT® D ARCTIC (CrN).
³ BALINIT® FUTURA NANO ARCTIC (TiAlN).